Linux Blog

APNIC Box – Linux on a Mikrotik 532a, Part 1 – The Device

Filed under: General Linux — davidapnic at 1:04 pm on Wednesday, November 5, 2008

I put this device together for fun sometime around the start of 2007. The ideas that spawned this was using OpenWRT on a Linksys WRT54G access point. A surprisingly powerful and full Linux distro with all kinds of advanced capabilities running on a Linksys wireless router which I’d previously thought to be a reasonably dumb device with computing power more comparable to a calculator than a PC. The project opened my eyes to embedded devices, and I wondered what device base I should start with. To cut a long story short and for reasons that I can’t even remember anymore I came across the Mikrotik Routerboard 532A and decided that I should start with that.

Conception

APNIC Box Image 1

APNIC Box Image 1

Here’s a picture of the device from the outside with some labels, view the full image to see them.

1. Status LEDs. Blue at the bottom left shows it’s on, orange at the top right shows that there’s wifi activity.
2. Ethernet (eth0)
3. Standard Serial Console (57600, 8 N 1)
4. Ethernet (eth1)
5. Ethernet (eth2)

You’ll notice a PicoLCD unit from mini-box.com on top of the device, I’ll dedicate a separate section to that. For the moment, eth0 connects to a switch and my local lan on the 192.168.100.0/24 range. eth1 holds a public IP and is connected to my first ISP via a ADSL2+ modem (I generally get about 14mbit down and 1.5mbit up stable), and eth2 is connected to the same provider via a separate ADSL2+modem (I get about 16mbit down and 1.7mbit here). The ISP does not bond these connections – I wish :-). They are two entirely separate connections to the same ISP. This isn’t for redundancy as realistically unless you use cable which isn’t available in my area, any fault will usually be with BT (the network/telecoms provider) and so using two separate ISPs won’t really add any great redundancy factor. BETHERE (my ISP) are the only UK ISP that I know of to offer the 24mbit down/2.5mbit up service. Anyway, I guess the speed difference over the two lines is down to one connection to the exchange being slightly shorter or maybe cleaner *shrug*

Article first published at: http://www.adamsinfo.com/apnic-box-linux-on-a-mikrotik-532a-part-1/

My Linux Desktop Machine

Filed under: Linux Hardware — TheLinuxBlog.com at 8:39 am on Saturday, November 24, 2007

Maybe its just me but I find it interesting to look at other peoples computer stuff so I’m going to take the time to write some blog posts about my hardware.

First in my lineup is my Desktop. This is by no means a new computer but runs very well.
CPU: AMD Athlon XP 2500+
Motherboard: MSI KT400
Memory: 512MB DDR 333
Hard Drive: 160GB Maxtor
Video Card: NVIDIA GeForce FX5200
Ethernet: ADMtek NC100 Network Everywhere 10/100
Media Devices: CD-RW, Floppy, ATA133 Hard Drive Bay
Monitor: LG 19″ Flat Panel. DVI, VGA, 1280×1024. 4ms 1400:1
Keyboard/Mouse: Generic Staples $10 special and a unknown brand painted laser mouse.

Every device is supported by the 2.6 kernel and Linux runs very well on it. The motherboard uses a VIA chip set and a C-Media audio device. The CPU is
actually 1875.733 MHz with a 512KB cache. According to cat /proc/cpuinfo it has a bogomips rating of 3754.8

Now comes the sensitive part, my distro of choice. For some this is a sour topic but I’ll just say that it doesn’t really matter to me. I run windows on it before and most Linux distributions out perform it out of the box (after installing video drivers.) I choose to run Slackware 12 on it because of the simplicity. It took a little while to configure it how I like but it turned out pretty well. I use slackpkg to keep it current.

I’ll be sure to post some pictures of the setup some time.

Thats about all I have to say about my desktop, if you have any questions or would like any additional information just give me an e-mail at: owen @ thelinuxblog.com